https://en.wikipedia.org/wiki/Nick_Piantanida

This guy was in a remote controlled, parachute equipped gondola at 17km altitude wearing a pressurized suite. His suit broke and even though the emergency descent of the gondola was immediately activated to descend safely, he later died from embolism (bubbles forming in the blood because of rapidly decreasing pressure). Passenger jets cruise at about 11km so i gather it would be similar.

OpenWRT does not use liblzma or systemd so i think that one is pretty safe. I would also be surprised if Android included OpenSSH server binaries in that way.

Uhhh you realize there are muskets hanging on the wall, right? I think its fair to say they don’t just make swords :)

that sounds almost exactly like the Reichsbürger in Germany. They also claim the current German state is actually just a corporation and the laws of the German empire are somehow still applicable. They also create their own passports. And of course they are deeply interconnected with Neo-nazis.

oh i must have missed a few orders of magnitude there. 6Mt of helium is a ridiculous amount though … what is all that used for? according to WA that is about the water volume of the three gorges dam at STP

Edit: just read the report, wow, more than a quarter of all the helium is used just for “breathing mixes” which i assume means its for scuba diving.

from the wiki article on Helium:

an estimated 3000 metric tons of helium are generated per year throughout the lithosphere.

I think the main issue here is not that we are loosing helium on a planetary scale but that the easy to reach helium from gas wells is wasted. We will never run out of helium at our current rate of consumption before the sun goes nova, if we consider all sources on earth, but it will get a lot more expensive and the supply will get less steady.

this is extra tricky because they did not specify the exact kernel. mainline could be any of the kernels tagged as stable that you can build from linus’ git tree. i know that in the past you could run a mainline linux on intel 368 chips but today you probably can not because official support was dropped a while ago.

datasheet for one of the drive models apparently these have a dual SAS interface, so what you are seing could be completely normal. i dont have any experience with this type of setup though.

btw you can uniquely identify partitions by using something like lsblk -o+PARTUUID,FSTYPE the partuuid should never repeat in the output even if the partition table was somehow used as a template (though "dd"ing from disk to disk will duplicate those of course)

also check out the “SERIAL” column for lsblk to uniquely identify the drives themselves.

could you run something like sudo lsblk -o+MODEL and note down the model for the drives? i kind of suspect that the HBA you are using is still doing some abstraction and is not in IT mode. the duplication could come from connecting two SAS cables to the same backplane, thus creating a sort of double image of the enclosure. this is usually handled and hidden by the HBA though if it is configured correctly.

pls also check that you are in fact using the correct ports on the enclosure. if you are not building a SAN only the “A” ports are supposed to be used and the “B” ports should be unused/free.

just a bunch of individuals drives

that is literally what JBOD means so congratulations you already have one. a classical RAID would show up as a single drive.

Initiator-target (IT) mode enables creating a JBOD with zfs vdevs on it. You can have the zfs vdevs in raidz configuration (which would give you the same drive redundancy as a hardware raid, with raidz1 performing similar to RAID5)

zfs is commonly used with a JBOD configuration on a raid controller but you can also use any other kind of controller as long as the individual drives can be written to. examples for this would be NVMe drives directly attached to the PCIe bus or normal SATA controllers. This is more a performance optimization than an issue with compatibility.

instead of putting a grub config in /boot/grub you could also try embedding it directly with grub-mkimage. you would need to point to the grub config that you have with -c and add all the needed modules as extra arguments at the end.

it is possible that the grub image you installed is just not looking for the config file at the right place.

or maybe try putting the grub.cfg in the same directory as the grubx64.efi

no i was just adding that to explain that grub needs special steps to work with secure boot enabled. if secure boot is off you can ignore that part.

is secure boot enabled in the firmware? It is possible that you have a signed grub binary installed but the module signing is not yet rolled out. Edit: my mistake: if you are using grub with shim then all the necessary modules need to be baked into the grub binary. maybe grub was not installed correctly?

click on the link pls

“ἰχθύς” is the ancient greek word for “fish” https://en.wiktionary.org/wiki/ΙΧΘΥΣ

yes indeed. i keep being confused how email can still suck so much sometimes when it had decades to mature.

yeah this is a real pet peeve of mine.

In German many people, web mailers and also sometimes even email software use “AW:” (short for AntWort) instead of “Re:” and then some of them don’t even recognize the existence of a previous “AW:” or “Re:” giving you such wondrous email subjects as: “AW: Re: AW: Re: AW: AW: Re: AW: Re: really important subject” 🤦

you h2e it?

woah this is awesome!

maglevs need classical wheel systems anyway because there might be a power outage, so simply having wheels that are compatible with the local rail system is a brilliant idea.

add in a tiny propulsion system so they can use the normal tracks at low speed without the help of the maglev tracks and you can sort of blend the two systems together in critical locations like switches and train stations.