I have a Nevermore filter with 24v fans, would it be fine to connect them to the parts that I have circled on my Prusa MK4?

Or is that dangerous?

  • Dangerhart@lemm.ee
    link
    fedilink
    English
    arrow-up
    11
    ·
    1 year ago

    You might be able to but you really shouldn’t. At the best you wouldn’t have control over fan speed. Find the wiring diagram for the board and use a fan header

    • chrischryse@lemmy.worldOP
      link
      fedilink
      English
      arrow-up
      2
      ·
      edit-2
      1 year ago

      Idk what type of connector my printer uses since my fan is different

      How about a raspberry pi?

      • FuglyDuck@lemmy.world
        link
        fedilink
        English
        arrow-up
        4
        ·
        1 year ago

        Pi’s are usually 5vs, they won’t drive a 24v fan happily at all.

        At that point what you can do is a power relay- like how most bed heaters work. That could be controlled by a pi, but delivers power from a 24v source.

          • FuglyDuck@lemmy.world
            link
            fedilink
            English
            arrow-up
            2
            ·
            1 year ago

            If the charger is a 24v powesupply, that would work. I would also suggest getting a switch to put in line so you don’t have to keep unplugging it- either a rocker switch or mini toggle.

            • chrischryse@lemmy.worldOP
              link
              fedilink
              English
              arrow-up
              1
              ·
              1 year ago

              Not sure how familiar you are with electronic stuff, but the fans I have are 24v and 0.1A my laptop charger outputs up to 6A that shouldn’t be an issue right?

              • FuglyDuck@lemmy.world
                link
                fedilink
                English
                arrow-up
                1
                ·
                1 year ago

                Volts need to match, nominally.

                Your fans will only draw .1A from the supply- as long as your supply has enough amperage to supply everything running… your fine.

                  • CmdrShepard@lemmy.one
                    link
                    fedilink
                    English
                    arrow-up
                    1
                    ·
                    1 year ago

                    With a fan it won’t be a big deal if the charger outputs 19-24V. Do you have a multimeter? Do you have a 24V source anywhere on the board? Using a laptop charger for 24V/0.1A is just way overkill. It’ll work just fine though. You might also get some 24V LEDs to run off it too since you’ll have all that extra current capacity.

                  • FuglyDuck@lemmy.world
                    link
                    fedilink
                    English
                    arrow-up
                    1
                    ·
                    1 year ago

                    19 is probably fine. Voltage is always a bit inconsistent so the phrase they use is “nominal”- or “more or less”

      • Dangerhart@lemm.ee
        link
        fedilink
        English
        arrow-up
        1
        ·
        1 year ago

        Powering the fan from gpio pins probably isn’t going to work out well either, they are 3.3v and 5v. Powering the fan from the PSU is going to be similar to powering a pi off it, I believe you should step the voltage down to what each needs, where the fan is 24v I think the pi is 5v. Your PSU is probably 115 or 220 v. For connectors I would expect to have to redo them yourself with micro fit, molex, jst or w/e you want and can get. On some of mine I just did single pin molex on the pins of the white female connector for fan headers, it doesn’t lock but it works if you don’t have a lot of movement. This page is awesome for connectors info https://www.mattmillman.com/info/crimpconnectors/common-jst-connector-types/

        • chrischryse@lemmy.worldOP
          link
          fedilink
          English
          arrow-up
          1
          ·
          edit-2
          1 year ago

          Seems complicated I might just connect it to and adapter I can plug my 24v laptop charger into or just getting a buck converter

      • Dangerhart@lemm.ee
        link
        fedilink
        English
        arrow-up
        1
        arrow-down
        2
        ·
        edit-2
        1 year ago

        Honestly if your going to go through all this effort to make this work, and already have a pi, I would suggest instead upgrade the control board to something with extra fan headers, led heads, etc and switch to klipper, there have to be guides out there for your specific printer

    • TwanHE@lemmy.world
      link
      fedilink
      English
      arrow-up
      1
      ·
      1 year ago

      Incase there’s no fan header left you can always get a variable buck converter with a rotary knob to manually set the speed on the fly atleast.